3D Printer Accessories V6 J-Head Hotend RepRap Extruder for 1.75mm Filament, Direct Feed or Bowden. w/ 0.4mm Nozzle, 12V fan, and 3ft PTFE Bowden Tube

This hot end is a replica of the newest, popular V6 hotend, this not only allows you to print extremely high temperature materials like PP/ Polycarbonate and Nylons but also eliminates typical hotend meltdown failures associated with other types of hotends. The latest hotend has a PTFE liner that slides inside the the upper portion of the heat brake, to help prevent misalignment of the filament, which is never subjected to high temperatures so there is no risk of damaging the liner through overheating.
For Marlin firmware, under THERMAL SETTINGS -> #define TEMP_SENSOR_X (X being your extruder #) you should use # 11: 100k beta 3950 1% thermistor (4.7k pullup)

Specification:
Type: V6 J-head, can be used either as bowden or direct feed style
Thermistor: NTC 3950 100K (Marlin users should use Table 11 to define temp sensor)

Package contents:
1 x Metal J-Head hotend for 1.75mm w/ 0.4mm nozzle
1 x NTC 3950 100K Thermistor, with leads and dupont connector
1 x 12V 40W Heater
1 x Heatsink shroud with 12V 0.13A High Speed Cooling fan
1 x 3ft long, 4mm OD, 2mm ID, PTFE Bowden tube
2 x Quick connect straight fittings

Product Features

  • 3D printer hotend, Metal J-Head v6 compatible hotend for 1.75mm filament, w/ 0.4mm nozzle
  • Heatsink Shroud and high speed, 12V 0.13A cooling fan / NTC 3950 100K thermistors, w/ leads and dupont connector
  • 12V 40W heater / 3ft long, 4mm OD 2mm ID PTFE bowden tube and quick connect fittings
  • Hot End can be used for: ABS, PLA, PETG, and most any other conventional print materials
  • This hot end can reach over 230C, for high temperature performance.

Detailed Information available on our Homepage…

Published by

Best 3D Printer Specialist

3D Printing. The next Goldrush is on it´s way. Inside information on how to start printing in 3D, where to buy Printers, how to use them, and the newest Pictures and reviews of available 3D Printers.

3 thoughts on “3D Printer Accessories V6 J-Head Hotend RepRap Extruder for 1.75mm Filament, Direct Feed or Bowden. w/ 0.4mm Nozzle, 12V fan, and 3ft PTFE Bowden Tube”

  1. Anet A8 Bowden conversion – Highly recommend I purchased this for my Anet A8 for a Bowden Extrusion Conversion. It works as expected and saved me something like $20 for going with a genuine hot end. It comes with enough tubing to plumb an Anet A8 twice, albeit I mounted my extruder motor behind the display screen (may vary depending on where you plan on putting it).I will say, in all honesty, I did not use the heater element and thermistor included. They appear to be equal/higher quality than what came from the manufacturer…

  2. Nice, inexpensive unit, works good. I had a very minor issue, and in less than an hour (on a sunday no less) after contacting them, they made it right.Will definitely deal with them again.This came with an any cubic branded fan; which for my setup was a bit weak for anything hotter than PLA ,and not cooling of the heatsink properly causing blockages. That was remedied quickly by swapping out the 12v fan for a 5v fan connected to 12v to get it to spin faster and push more air. I also flipped the fan around so that it…

Leave a Reply

Your email address will not be published. Required fields are marked *