[Sintron] 3D Printer Kit , Ramps 1.4 + Mega 2560 + 5pcs A4988 Stepper Driver w/ Heatsink + LCD 12864 Smart Controller + 3 Pcs End Stop + Mk2b Heat Bed + 2 Pcs Pulley + 2m Gt2 Belts for Reprap Prusa i3

Overview:

This kit is a good start for starter to build your own 3D printer. basically once you get the electronic parts done. then later it would be more easier to complete the rest parts.and yes, this is almost all the electronics you need for your 3D Printer.(except motors and extruder hotend)
If you are not sure what you need to complete your 3d printer project, please feel free to ask. We not just sell them, we also provide professional after-sales service, We will offer you a detailed tutorials including project introduction and their source codes. so welcome to discuss with us, we will try to do technical support as much as we can.

(1)3D Printer Controller RAMPS 1.4 – You can check:https://www.amazon.com/dp/B06WP5DDP1

(2)Mega 2560 R3 – You can check:https://www.amazon.com/dp/B00E94CGTQ

(3)LCD 12864 Graphic Smart Display Controller – You can check:https://www.amazon.com/dp/B00L72FAZU

(4)A4988 Stepper Motor Driver with Heatsink – You can check:https://www.amazon.com/dp/B00JXGT1G6

(5)Mechanical Endstop Switch – You can check: https://www.amazon.com/dp/B00OCFEZ1O

(6)2M GT2 Belt + 2 pcs GT2 20 Tooth Pulleys – You can check: https://www.amazon.com/dp/B00OFUZSP8

(7)MK28 Heatbed:This is the latest version of MK2B,100% compatible with all Prusa and Mendel 3d printer variants.

Package List:

(1)3D Printer Controller RAMPS 1.4 x1
(2)Mega 2560 R3+USB Cable x1
(3)A4988 Stepper Motor Driver with Heatsink x5
(4)LCD 12864 Smart Controller x1
(5)MK28 Heatbed with Thermistor and High Temp Wire x1
(6)Mechanical Endstops x3
(7)2M GT2 Belt+20 Tooth Pulleys x2
(8)Smart Adapter x1
(9)30cm Cable x2
(10)Storage Box x1

Product Features

  • (1) 3D Printer Controller RAMPS 1.4 x 1 + Mechanical Endstops x 3
  • (2) Arduino-Compatible Mega 2560 R3 With USB Cable x 1
  • (3) A4988 Stepper Motor Driver With Heatsink x 5
  • (4) LCD 12864 Graphic Smart Display Controller Kit x 1
  • (5) MK28 Heated Bed with Thermistor and High Temp Wire x 1

Click Here If You Need More Detailed Info…

Published by

Best 3D Printer Specialist

3D Printing. The next Goldrush is on it´s way. Inside information on how to start printing in 3D, where to buy Printers, how to use them, and the newest Pictures and reviews of available 3D Printers.

2 thoughts on “[Sintron] 3D Printer Kit , Ramps 1.4 + Mega 2560 + 5pcs A4988 Stepper Driver w/ Heatsink + LCD 12864 Smart Controller + 3 Pcs End Stop + Mk2b Heat Bed + 2 Pcs Pulley + 2m Gt2 Belts for Reprap Prusa i3”

  1. Worked great from day 1, no issues at all. This is my first hotend purchase since I am just getting into 3D printing. Read a lot of reviews and decided to get this one. Was not disappointed. Came fully assembled and has worked right since I installed it. It has never jammed the filament once in the weeks I have been using it. The only complaint I have is that it can be hard to refeed the filament when I accidentally retract it too far, but that’s only because of how I have it mounted on my frankenprinter, so not the fault of the…

  2. Well that’s interesting, It printed amazingly; I thought I was going to have to tear it down and re-bore/smooth out the inside.It was basically just a swap. The only bad part about this unit I would say would be to motor. The wires go directly into the unit and can’t be removed so if you need to remove the unit to clean you’ll have to dissemble the the front section to separate it from the motor if you have your motor cables wrapped up.I’ve had one instance where the thermal…

Leave a Reply

Your email address will not be published. Required fields are marked *