CCTREE 15PCS 3D Printer Heating Block Cotton with Kapton Tape Hotend Nozzle Heat Insulation Cotton for Ultimaker/Makerbot/Creality CR-10

Specification
Material: cotton
Cotton Size: 70mm x 20mm x 2mm
Kapton:Width 6mm, Lenght:33M
Feature: heat preservation

Note: this product only suitable for 3D printer using indoors

Attention: Small parts, keep away from children

Package including:
15PCS x 2mm heating block cotton
1PCS x6mm Kapton Tape

WARNING!!
1.3D printer replacement parts, Always shut off power to the circuit before starting installation work.
2.The surface temperature of the 3D printer might be high, and be careful not to touch the heating element to prevent injury.
3.3D printer initial operation, Do not run the equipment Unattended state.
4.When printing with a PLA(190°C-230°C) or ABS(230°C-250°C)consumable, if the temperature sensor and other accessories fail, it may cause high temperature hazards. Do not run the equipment Unattended state.
5.To ensure the users will use the product safely and properly, Please read your 3D printer manual first and follow the instructions step by step before using the product.
6.Due to the variety of possible end-uses, it is ultimately the responsibility of the customer to determine a product’s suitability for a particular application.

Product Features

  • Heat preservation, keep the printer heating evenly and work better
  • You can Punch Holes or Cut fit size to the cotton.
  • Recommend Safe Working Temperature : <300°C
  • Cotton Size: 70mm x 20mm x 2mm Kapton:Width 6mm, Lenght:33M
  • Package including:15PCS x 2mm heating block cotton + 1PCS x 6mm Kapton Tape

Visit The Website For More Information…

WINSINN 3D Printer Optimized Extruder Hotend Kit Driver Feeder For 1.75mm 3mm Nozzle Filament – RepRap Prusa i3 Bowden E3D J-Head V6 Makerbot MK8 MK10 Kossel Delta Universal Upgrade Accessories Parts


►This is a Optimized version of 3D Printer Extruder. It is very light and compact. It can use a lighter motor, any Bowden-type 3D printer can become a powerful, reliable little beast. It is easy to manually squeeze, remove, load and unload Filament.
At the same time, You only need a hex wrench, you will be able to within a minute to remove the Titan, regardless of the opening and assembly are very easy and fast.

—————————————————————————————————————

►Installation Points: The top surfaces of the two gear s must be flush adjust the pinion accordingly

►We have done thousands times of tests, including strength testing, time testing and so on. It really works well. Let’s try it:))

—————————————————————————————————————

Package include:
►1 x WINSINN Extruder Full kit (All Accessories show as Picture 2)
►Note: This Kit NOT Included Motor, V6 Hotend, Titan Aero

►We offer the best products and services, if there has any problems, you can tell us anytime. Thank you:))

Product Features

  • Compatible with E3D-V6 Hotend and Titan Aero Upgrade Kit
  • High quality Titan extruder, Very easy to upgrade your printer
  • Filament:1.75mm 3mm PLA / ABS / Flexible / other
  • Suitable For Remote and Short distance
  • Note: This Kit NOT Included Motor, V6 Hotend, Titan Aero

Visit The Website For More Information…

Wangdd22 3D Printer J-head Dual V6 Head Extruder Hotend with 0.4mm Nozzle 12V Cooling Fan and M4 Fisheye Effector Hanging Station for 1.75mm Filament

Description:

V6 Extruder:
●With PTFE in hot regions of our HotEnd we can reach 260C with the supplied thermistor. By swapping a thermistor for a thermocouple (may require additional electronics) you can reach over 280C.
●This not only allows you to print extremely high temperature materials like PP/ Polycarbonate and Nylons but also eliminates HotEnd meltdown failures associated . latest v6 hotend has a PTFE liner inside the hotend this liner is never subjected to high temperatures so there is no risk of damaging the liner through overheating.
●Our new HeaterBlock gives the fastest heat up times and the most responsive temperature control by clamping around the cartridge for maximum thermal contact. The new thermistor placement means you get the most accurate temperature readings with the fastest response. What this means for you the user is that you can go from 20C to 200C in just 65 seconds, temperature control is responsive enough that you can keep the hotend within 0.5C of your set temperature or less with ease.
Specification:
Type: Bowden J-head Dual V6 Hotend
Included: NTC3950 thermistors and 12V 40W heater
NTC 3950 Thermistor parameters:
High accuracy: 1%
Resistance value at 25°C=100K
Wiring insulation: high temperature teflon/PTFE
Wiring length: 1 meter

Fisheye Effector:
Material: Aluminium Alloy
Scrwe size: M4
This effector fits V6 J-head hotend (bowden and wade),it can hold two J-head together.
Don’t compatible with chimera multi-extrusion hotend and V5 version J-head hotend.

Package includes:
2x long distance V6 J-head extruder with 0.4mm nozzle ,12V heater
2x 12v cooling system
1x dual head M4 effector

Product Features

  • RepRap 3D printer extruder hotend compatible with E3D V6 1.75mm / 0.4mm
  • 12V 40W heater, 12V high speed fan with shroud, NTC 3950 pre-wired thermistor
  • Metal construction with PTFE liner inside, good for ABS, PLA and other conventional print materials
  • Easy No-Solder, No-Tape, No-Adhesive assembly and maintenance.
  • This 3D Printer Dual V6 Hotend is applied for 1.75mm Filament Long-Distance Filament Bowden extruder

Detailed Information available on our Homepage…

[Sintron] 1.75mm 3D Printer Drucker Kossel Mini All Metal MK8 Extruder hotend 0.4mm Nozzle for Bowden RepRap Rostock Delta Kossel Mini Prusa i3 (Kossel-Extruder)

Overview

This MK8 extruder is an open source universal suitable for most RepRap and DIY long distance feeding filament 3D Printers.

We have made the NEMA 17 Stepper motor with 4 wires which is specially designed for 3D Printer Controller RAMPS 1.4, so you just need to plug it in, and there you go! no need to buy from others and waste a lot of time trying to figure out how to connect them.

The extruder is almost the most important part for 3D printer, also the most difficult part to calibrate. we have made all metal design to replace plastic parts bowden extruder.

Features

(1) Compatible with ABS and PLA 1.75mm.
(2) NEMA 17 Stepper motor is included in this transaction.

Tips:

While using with PLA filament, please always remember to keep the fan on, otherwise it might get jammed and ruin the hotend. PLA is more easier to get jammed, so it might require some patience to practice.
For ABS, we would also suggest to keep the fan on, as this is also better. also remember to purchase filament from good reputation seller, as the filament is very important!

Specifications
(1) Nozzle : 0.4mm
(2) Voltage : 12V/24V
(3) Motor Model : SL42STH40-1204A
(4) Nozzle Flow Rate : 24cc / h
(5) Thermistor Tpye : NTC 100K 3950
(6) Sports Shaft Speed : 10-100mm

Motor Parameters

(1) Model:SL42STH40-1204A
(2) Step Angle : 1.8°
(3) Rated Voltage : 2.55 V
(4) Rated Current : 1.7 A
(5) Phase Resistance : 1.5Ω
(6) Phase Resistance : 2.3 mH
(7) Number of Lead Wire : 10-100mm

Product Features

  • (1) Compatible with ABS and PLA 1.75mm.
  • (2) NEMA 17 Stepper motor is included in this transaction.
  • (3) We don’t just sell them, we also provide good after-sales service, so welcome to discuss with us, we will try to do technical support as much as we can, please feel free to send us an email, we will also help you to complete the project !

Visit The Website For More Information…