BIQU Smart Display Controller Ramps 1.4 2004LCD Controller with Adapter for 3D Printer RepRap Adapter

Specifications:
This panel connect your RAMPS 1.4, you do not need your computer, your SD card intelligent controller power supply. All further operations, such as calibration, the axis movement can be done only with a rotary encoder intelligent controller. 3D design print without a computer, just use the G code design stored on the SD card.

Package Included:
1*2004LCD Controller( SD Card Not Included)
1 *Connector
2 *30cm cables

Product Features

  • Popular RepRap 3D Printer LCD Controller and SD Card Reader
  • The intelligent controller includes an SD card reader, rotary encoders and a 20-character × 4 line LCD display
  • You can easily connect it to your RAMPS 1.4 board using “smart adapter” included
  • 3D design print without a computer, just use the G code design stored on the SD card
  • With Smart LCD Controller you can print 3D designs without USB connection to your computer

Click Here For More Information

HESAI 3D Printer Kit Smart Parts RAMPS 1.4 Controller Control Panel LCD 2004 Module Display Monitor Motherboard Blue Screen

Description:

The intelligent controller includes an SD card reader, rotary encoders and a 20-character × 4 line LCD display. You can easily connect it to your RAMPS 1.4 board using “smart adapter” included.

This panel connect your RAMPS 1.4, you do not need your computer, your SD card intelligent controller power supply. All further operations, such as calibration, the axis movement can be done only with a rotary encoder intelligent controller. 3D design print without a computer, just use the G code design stored on the SD card.

Package List:

1x LCD 2004 Smart Controller

1x Smart Adapter

2x FC Cable

Product Features

  • Popular RepRap 3D Printer LCD Controller and SD Card Reader
  • Included adapter for RAMPS 1.4 board
  • Fully supported by Marlin firmware
  • With Smart LCD Controller you can print 3D designs without USB connection to your computer

Visit The Website For More Information…

[Sintron] 3D Printer Kit , Ramps 1.4 + Mega 2560 + 5pcs A4988 Stepper Driver w/ Heatsink + LCD 12864 Smart Controller + 3 Pcs End Stop + Mk2b Heat Bed + 2 Pcs Pulley + 2m Gt2 Belts for Reprap Prusa i3

Overview:

This kit is a good start for starter to build your own 3D printer. basically once you get the electronic parts done. then later it would be more easier to complete the rest parts.and yes, this is almost all the electronics you need for your 3D Printer.(except motors and extruder hotend)
If you are not sure what you need to complete your 3d printer project, please feel free to ask. We not just sell them, we also provide professional after-sales service, We will offer you a detailed tutorials including project introduction and their source codes. so welcome to discuss with us, we will try to do technical support as much as we can.

(1)3D Printer Controller RAMPS 1.4 – You can check:https://www.amazon.com/dp/B06WP5DDP1

(2)Mega 2560 R3 – You can check:https://www.amazon.com/dp/B00E94CGTQ

(3)LCD 12864 Graphic Smart Display Controller – You can check:https://www.amazon.com/dp/B00L72FAZU

(4)A4988 Stepper Motor Driver with Heatsink – You can check:https://www.amazon.com/dp/B00JXGT1G6

(5)Mechanical Endstop Switch – You can check: https://www.amazon.com/dp/B00OCFEZ1O

(6)2M GT2 Belt + 2 pcs GT2 20 Tooth Pulleys – You can check: https://www.amazon.com/dp/B00OFUZSP8

(7)MK28 Heatbed:This is the latest version of MK2B,100% compatible with all Prusa and Mendel 3d printer variants.

Package List:

(1)3D Printer Controller RAMPS 1.4 x1
(2)Mega 2560 R3+USB Cable x1
(3)A4988 Stepper Motor Driver with Heatsink x5
(4)LCD 12864 Smart Controller x1
(5)MK28 Heatbed with Thermistor and High Temp Wire x1
(6)Mechanical Endstops x3
(7)2M GT2 Belt+20 Tooth Pulleys x2
(8)Smart Adapter x1
(9)30cm Cable x2
(10)Storage Box x1

Product Features

  • (1) 3D Printer Controller RAMPS 1.4 x 1 + Mechanical Endstops x 3
  • (2) Arduino-Compatible Mega 2560 R3 With USB Cable x 1
  • (3) A4988 Stepper Motor Driver With Heatsink x 5
  • (4) LCD 12864 Graphic Smart Display Controller Kit x 1
  • (5) MK28 Heated Bed with Thermistor and High Temp Wire x 1

Click Here If You Need More Detailed Info…

HESAI 3D Printer Controller Kit for Arduino Mega 2560 R3 Board + RAMPS 1.4 Control Panel + LCD 12864 Motherboard Display + 5pcs DRV8825 Stepstick Stepper Motor Driver Module + Heat Sink

MEGA 2560 R3 Board

The Mega is 100% compatible with Arduino and most shields designed for the Arduino

The chip is Atmega2560-16au and Atmega16u2, same with the official version.

Improved and expert version: 1.0 pinout: added SDA and SCL pins that are near to the AREF pin and two other new pins placed near to the RESET pin, the IOREF that allow the shields to adapt to the voltage provided from the board. In future, shields will be compatible both with the board that use the AVR, which operate with 5V and with the Due that operate with 3.3V. The second one is a not connected pin, that is reserved for future purposes.

Stronger RESET circuit.

It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with an AC-to-DC adapter or battery to get started.

RAPMS 1.4 Controller

Fully assembled & tested, no soldering required

Designed to fit the entire electronics needed for a RepRap in one small package for low cost.

Modular design includes plug in stepper drivers and extruder control electronics on an Arduino MEGA shield for easy service, part replacement, upgrade-ability and expansion.

A number of Arduino expansion boards can be added to the system as long as the main RAMPS board is kept to the top of the stack.

Version 1.4 uses surface mount capacitors and resistors to further cover edge issue cases.

LCD 12864

Using a large screen 12864LCD.

With a SD card base on back, put slicing file into the SD card and select the file on the LCD, then can be printing.

Product comes encoder parameter adjustment can be achieved, and the file selection print.

Plug and play on the RAMPS, but need to modify the firmware to support.

Package List:

1x MEGA 2560 R3 Board

1x RAMPS 1.4 Controller

1x LCD 12864

5x DRV8825 Driver

5x Heat Sink

1x Screwdriver

Product Features

  • Fully assembled & tested, no soldering required
  • Designed to fit the entire electronics needed for a RepRap in one small package for low cost.
  • Modular design includes plug in stepper drivers and extruder control electronics on an Arduino MEGA shield for easy service, part replacement, upgrade-ability and expansion.
  • A number of Arduino expansion boards can be added to the system as long as the main RAMPS board is kept to the top of the stack.
  • Version 1.4 uses surface mount capacitors and resistors to further cover edge issue cases.

Click Here If You Need More Detailed Info…